Product Information

MiniBle S Shower Version;

Material:SUS 316 Medical Grade Stainless Steel
Net Weight:90-100g
DimensionØ2.55x4cm
Intake Port:M22 female、G1/2 male

Water Output Port:G1/2 female
Suggested Water Pressure:>1.5kg/cm^2
Warramty:One Year
Parts and accessories:MiniBle S Shower Body, Rubber Washer Screen, 16mm gasket x2, G1/2 – M22 Male Adapter, User Manual, Dedicated M3 Screwdriver, Tweezer

Free Gift: Doris Shower Head, Hose, 16mm gasket x2

 

 

Notices

  • Please install thread with care.

  • Cautious with your hands when using hot water as MiniBle S is made by SUS 316 Medical Grade Stainless Steel.

  • It is microbubbles’ main feature to enhance the detergency of water. If the water from water outlet is not drinkable, please do not drink it directly.

  •  To prolong the service life, please clean the product at least once a month. To check the detailed cleaning method, please see Cleaning And Maintenance. (The actual cleaning frequency and service life may vary with different water quality.)

  • As MiniBle S saves water by 30-50%, the using experience may need to be adapted.

Detailed Description-

Water Description
The water pressure of MiniBle S is 1.5kg/cm^2, product can be used when meeting one of the conditions listed below:

  1. Has pressurized motor at home

  2. The floor you are at is above five floors apart from the top floor 

Installation Guideline

​FAQ-

MiniBle Adapter Sticks. What can I do?

You can use a ten – dollar coin, level the groove on the adapter, and remove it.

Why my MiniBle S Shower leaks from the middle of adapter and hose, or from the MiniBle and shower head?
  Please check if the installation steps are correct, and whether there are rubber washer screen and gasket putted inside. The correct installation steps should be: Shower Hose > 16mm Gasket > 16mm Adapter > Rubber Washer Screen > MiniBle S Shower Version > 16mm Gasket > Shower Head Full Installation Guideline: Detailed Information > Installation Guideline

 Why MiniBle S Shower Version Leaks from The Air Hole?
   Please use with the Doris shower head. If using your own shower head, due to the water pressure ratio and the amount of water flow, back pressure may occur and the air hole may seep.

There Seems to Have No Milky White Color Water From The Shower Handle After Installing MiniBle S Shower Version
    When microbubbles flow through shower head, the bigger ones would burst during the water flow, which could cause the not - so - obvious milky white color on visual inspection. However, the micro/nano bubbles would not decrease. Through tested, the amount of bubbles are quite the same before and after the water flow through shower head. Also, microbubbles and nanobubbles both have the efficiency in cleaning.

My MiniBle S Shower Version Is Not Attached With The Shower Head, Why Still Can’t I See The Milky White Color?

  1. Please check if the water pressure is right! (MiniBle S should be above 1.5kg/cm^2.)

  2. Please check if the installation steps are correct. The correct installation steps should be: Shower Hose > 16mm Gasket > 16mm Adapter > Rubber Washer Screen > MiniBle S Shower Version > 16mm Gasket > Shower Head If the steps are switched, it will not produce microbubble normally. Full Installation Guideline: Detailed Information > Installation Guideline

  3. Observation Method: the angle of the light will affect the observation of bubble. It is suggested that you use a transparent container to observe.
  4. Make sure the air hole is clear: the air intake will affect the produce of bubble. Therefore, it is suggested that you clean MiniBle first.

Notice: If the above steps cannot solve the problem, please contact us!

 

   Why some taps can produce milky white color, while some cannot?
   Different pipelines will affect the amount of water and water pressure. You can change another faucet to install MiniBle.

   Why water was milky white color before, but it is not now?
   The scale may block MinlBle’s air hole. You can wash MiniBle and use it again. If it still does not work, please contact us.

   After installing MiniBle, the hot water is not hot enough or is unstable.
   You can fix the problem by adjusting the water heater. The suggested steps are as following:

  1. Turn the water output of the water heater to the utmost.

  2. Turn the faucet to the hottest and water output to the utmost. Then, turn the water output to the one you used to.

  3. Turn the faucet to the hottest and water output to the utmost. Then, adjust the water heater to the temperature you used to.

   After adjusting the water heater, you can turn to the hottest temperature when using.

 

 Where Can I Purchase Doris Shower Head?
   You can purchase it at our official online shop!

 

Cleaning and Maintenance-

​   It is suggested to wash MiniBle S at least every month. Suggested steps: remove the rubber washer screen, unscrew the water hole, then clean every part with toothbrush with soft brush.If you MiniBle S has heavy scale, it is suggested to add citric acid into boiled water, then soaks MiniBle S.(Cleaing Guideline) Notes: The gasket, and rubber washer screen cannot soak into the citric acid. (The actual cleaning frequency and service life of product may vary with the water quality.)

 

Contact Us

If having any other questions, you can contact us with:
Email: ​info@herhers.com.tw
Tel:07-3590981 (10:00~18:00)
FaceBook: MiniBle迷你波微氣泡起波器
Offical Line@:@herhers
Service Hour:Mon. – Fri. 10:00-18:00​

已加入購物車
網路異常,請重新整理